Upload S7-300 Siemens Program using Ethernet cable

Dear PLC Technical members,

Welcome to our followers on the Blog PLC Technical, our topic today is very important this is what everyone's looking for it, this article show you step-by-step how to upload Siemens S7-300 program over Ethernet câble.

I. Upload S7-300 Siemens Program using Ethernet cable

As you saw in the title about how to upload S7-300 Siemens program over the Ethernet/IP cable for PLC Siemens to PC. Today we'll cover twelve points of interest and make sure you're going to get amazing results.

Before we begin, the uploading S7-300 Siemens Program with the Ethernet cable, let us take a look at CPU 317F-2PN/DP and The Difference between Ethernet and Profibus DP

1. Siemens S7-300 CPU317F-2 PN/DP

Siemens S7-300 CPU317F-2 PN/DP, One interface MPI/DP 12mbit/s, 2. interface Ethernet Profinet, with 2 port switch, With 1.5 Mbyte working memory, micro memory card necessary.

1.1 Profibus DP 

A Profibus connection port it look just like a standard DB9 serial connector. Most Profibus cable,some Profibus-DP connectors have a go through the port on the rear of the connector with the goal that you would daisy be able to bind another gadget to the bus.

Note that the two sorts of connectors have a red switch on the back, this switch must be set the on position on the last gadget and off for each other gadget.

1.2 Profinet PN

Profinet is a more current Ethernet-based Industrial correspondences convention the physical interface utilized for Profinet is a standard RJ45 Ethernet jack.

Profinet links are effectively conspicuous by their green shading while now and again a standard Ethernet link might be utilized to interface with Profinet gadgets official Profinet links ought to be utilized as they contain vigorous protecting enter intended to work well in unforgiving mechanical conditions.

Profinet works at 100 megabits for each second and links might be up to 100 meters long because of its fast activity and a reaction season of short of what one millisecond.

Profinet utilizes the indistinguishable physical association guidelines as Ethernet standard Ethernet switches can be used to broaden your framework.

Profinet devices have three different types of addresses an IP address a MAC address and a device name.

Please check this link:

By visiting this article you can find out how to Upload S7-300 Siemens Program using MPI cable

2. Basics To Upload S7-300 Siemens Program

In today's explanation we will look at: 

1. Click Start->Run, type cmd and press Enter.
2. Click ipconfig and press Enter. 
3. Right-Click on the Network icon on the bottom right of your taskbar, then select Open Network and sharing center.
4. Click to change adapters settings, Process to right-click on the network and choose Properties 
5. Set up the PG/PC interface 
6. Select the access path. At that point set the TCP/IP convention for the system card utilized. Click "Properties". Select the "IP address" alternative in the"Properties" discourse box
7. Click Diagnostic then chooses the Test and press Enter OK
8. Intel (R) 82579LMGigabitNtwork Connection.TCPIP.1 
9. Connect the Ethernet cable Cat5e is plugged into the gateway LAN4 Port
10. Create a new project in STEP 7
11. Let upload S7-300 Siemens program PLC, we have selected upload station to PG
12. We take the source of the CPU

Here is a detailed, continued explanation so that you can make the most of the explanation.

Step1: Click Start->Run, type cmd and press Enter.

Step2: Click ipconfig and press Enter

Step3: Right-Click on the Network icon on the bottom right of your taskbar, then select Open Network and sharing center.

Step 4: Click change adapters settings, Process to right-click on the network and choose Properties

Step 5:Set up the PG/PC interface: Select "Start > SIMATIC > STEP 7 > Customize PG/PC interface". Result: The exchange box for setting the PG/PC opens.

Step 6: Select the access path. At that point set the TCP/IP convention for the system card utilized. Click "Properties". Select the "IP address" alternative in the"Properties"

Step 7: Click Diagnostic then chooses the Test and press Enter OK

Step 8: if you use an Intel (R) 82579LMGigabitNtwork Connection.TCPIP.1

Step 9: Connect the Ethernet cable Cat5e is plugged into the gateway LAN4 Port as is shown in Figure

Step 10: Create a new project in STEP 7 Software

Select the menu file> New Enter a name for your project 

Step 11: Let upload S7-300 Siemens Program PLC, we have selected upload station to PG

Step 12: In this upload we have a selection the link of source CPU 317F-2PN/DP, here we have selected CPU with the IP:192.1.6.41

CPU 317F-2PN/DP

Step Final: here we take the source of the CPU

From here we have finished the subject of the upload S7-300 Siemens Program using Ethenet cable from PLC to PC, if you like it, please share it with friends until it benefits, and then meet on a new topic on blog PLC Technical.

Regards, 

PLC Technical